Measurement Procedure

  •        Pour the sample into the sample cell
  •        Place the sample cell on the sample holder
  •        Set to the measurement condition
  •        Press the "MEAS" button to start the measurement
  •        Instrument displays the results and data output
  •        Calibration


New Software features allow up to 15 separate calibration curves. There are three sets and each set represents 5 separate calibration curves. The Software also allows the users to choose between linear or quadratic curves. Calibration curves are restored manually without having to recalibrate as long as coefficients value/calibration data are on hand.

Original Sample Cell

To ensure accuracy and reliability of the analysis, HORIBA has maintained its original sample cell. By using the sample jig tool provided, you can easily seal the sample so that it is leak free.

Expanded Measurement Range (0~9.9999wt%)

This new model can measure a wider range of sulfur content. It has an expanded range to measure from 0-9.9999 wt% sulfur, due to the higher sulfur concentrations of crude and shale oil markets.

Large printouts

Printouts show important information, including sample ID, X-ray spectrum, date and time, measurement average value, standard deviation and calibration curve graph.

Data output

The printout is available in an 80 mm wide format for easy comprehension.

Safety mechanism

The SLFA-60 has a protective membrane covering the cell window to prevent the detector and X-ray tube from accidental sample leakage. This protective membrane unit is simple to assemble and replace.

Large screen display for easy viewing

The screen will display real-time data to check the measurement conditions.

USB memory

Your measurements can be recorded three different ways; by printout, exported to a USB memory device, or exported to an external PC through a USB interface, making it possible track and analyze the information throughout the lifetime of the unit.

Manufactured by HORIBA Scientific

Measurment principle

Energy Dispersive X-ray Fluorescence Analysis Method (EDXRF)

Measurement sample

Sulfur in Petroleum products such as heavy oil, naphtha, and crude oil, light oil

Measurement range

0 - 9.9999 %


15 ppm or less (with a 1 % sulfur sample)

C/H error correction

± 50 ppm or less per C/H (with a 1 % sulfur sample)

Lower detection limit

20 ppm or less (three times the standard deviation with a 0 % sample)

Number of calibration curves

5 lines × 3 sets (Total 15 lines)

Calibration curve order

Linear or quadratic (both automatic selection and manual settings available)


Calibration made using calibration points: (5 - 20 points)

Sample requirement

4 - 10 ml

Measurement time

10 - 600 sec

Spectrum measurement

Energy Axis: 0 - 10 keV, spectrum analysis to verify instrument preformances.

External output

USB connect with PC, USB memory

Ambient Conditions


+ 5°C ~ + 40°C (+ 41°F ~ + 104°F)


80% max relative humidity in temperature range + 5°C ~ + 30°C (+ 41°F ~ + 86°F).
Linear decrease to 50% relative humidity in temperature range + 31°C ~ + 40°C (+ 88°F ~ + 104°F).

Power and Housing

Power supply

AC 100 - 240 V ± 10 %, 50/60 Hz

Power consumption

80 VA

Dimentions [WxDxH]

230 x 400 x 140 mm (9 x 15.75 x 5.5 in.)


9 kg (20 lbs.)

Comformity Standards

ASTM D4294(USA)·ISO 8754·JIS K2541/B7995


Cross Section of Sample Cell and Detector

Dimentional Outlines

Tags: HORIBA, Sulfer in oil, ASTM D4294, ISO 8754 or JIS K2541/B7995.

Instruments upgrade

PT. HORIBA Indonesia

Ruko Jalur Sutera Jl. Jalur Sutera Blok 20 A No. 16-17 Tangerang, Banten 15144, Indonesia

Tel: +62 (21) 30448525
Fax: +62 (21) 30448521